Code Alarm PC 7400 Spezifikationen Seite 8
- Seite / 92
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
DS7400Xi Ver. 3+ Reference Guide Copyright © 2004 Detection Systems, Inc. P/N: 28995K Page 8
2.0 Enclosure Installation
The DS7400Xi control/communicator and the enclosure are shipped
together. The control, however, still needs to be installed into the
enclosure. Hardware for mounting the enclosure to a wall, and the
control to the enclosure is located in its own hardware pack.
2.1 Install the Enclosure
• Use the enclosure as a template and mark the top mounting holes
on the mounting surface.
• Pre-start the mounting screws for these two holes. Slide the en-
closure onto these mounting screws so that the screws move up
into the thinner section of the holes. Tighten the screws.
• Screw in the remaining two screws in either set of bottom mount-
ing holes.
• Knock out the desired wire entrances on the enclosure.
2.2 Install the Control/Communicator
The control is static sensitive. Make sure you touch
earth ground before handling the control. This will dis-
charge any static electricity in your body. Example:
Run the ground wire to the enclosure before handling
the control. Then keep holding the ground wire while
installing the control.
• Insert the three support posts into the control retainer holes as
shown in the diagram.
• Slide the top of the control into the retainer tabs (the slots under
the top frame).
• Once in the retainer tabs, the control will rest on the three support
posts.
• Secure the bottom of the enclosure by screwing the bottom three
holes through the support posts and through to the control re-
tainer holes.
Once the control is installed, be sure to connect its
ground wire to the top hinge of the enclosure (the
unpainted tab).
C
ircuit board
Enclosure
Support Post Assembly
Control/Communicator
Ground Wire
Progra
m
Pads
Retainer Tabs
Control Retainer Holes (3 places)
Wire Entrances (6)
Enclosure
Ground Tab
Flip-up view to show retainer tabs
Support Posts
IMPORTANT
NO STATIC
- Reference Guide 1
- Control/Communicator 1
- Table of Contents 2
- 1.0 Specifications 4
- 1.15 Max. Load Currents 5
- 1.17 Standby Current Load 5
- 1.18 Options 6
- 2.0 Enclosure Installation 8
- 3.0 Control Terminal Wiring 9
- DS7400Xi 10
- 5.0 System Worksheet 11
- Equipment Location and Notes 11
- Misc. Notes 11
- 12
- 2, KitchenSZ 13
- Zone Location and Notes 13
- Zn Funct. 1 13
- 6.0 Glossary 15
- 6.3 Zone Programming 16
- 6.4 Output Programming 17
- 6.13 Report Programming 19
- Programming 20
- 6.16 FCC Compliance Notice 20
- 7.0 Operating Guide 22
- [Master Code] + [#] [0] 23
- [0] [1] 23
- [1] [2] 23
- [0] [1] through [3] [1] 23
- Enter a PIN 24
- Enter [#] [9] [9] 24
- [Duress Code] + [Off] 26
- 7.12 Emergency Keypad Alarms 27
- 7.13 Fire 27
- 7.11 Fire Reset/Fire Trouble 27
- 7.14 Testing 28
- [PIN] + [#] [8] [5] 29
- [PIN] + [System Reset] 29
- [PIN] + [#] [8] [3] 30
- [PIN] + [#] [8] [6] 30
- [PIN] + [#] [8] [7] 31
- 8.0 Keypads 32
- 8.5 Single Partition Mode 33
- Feature 1 34
- 0 1 2 3 4 5 6 34
- Feature 2 34
- Feature 3 34
- Zone Function 35
- 11.0 Programming 36
- Programming a Zone 37
- Disable a Zone 0 38
- Select Option 42
- Data Dig 42
- Select Option DD 42
- Select Option D 44
- Ground Fault Detect Off 46
- Ground Fault Detect On 46
- No Events 51
- Opens and Closes 51
- All Other Events 51
- Data Digit 54
- Receiver 57
- Call-Out Minute 62
- Call-Out Hour 62
- 34 84 54*34 94 34 14*24 63
- Address 3914 68
- Pager Delay Time 68
- UL Application 69
- 12.3 Programming the DS7400Xi 70
- 12.5 Commercial Fire Alarm 71
- Ademco AB-12 Bell/Housing 72
- 13.0 Report Programming 73
- 13.2 BFSK Format 74
- 13.4 Pager Format 75
- Pager Format (Continued) 76
- 14.1 SIA Formats 77
- 14.1 SIA Formats (Continued) 78
- 14.2 CID Formats 79
- Sens/Contact 009 80
- Press # to Prog 80
- Mux Zone 80
- Enter Zone 80
- 16.0 Troubleshooting Guide 81
- 16.2 Reporting Problems 82
- 16.3 Zone Problems 82
- 16.4 General System Problems 83
- 17.0 Program Addresses 87
Verwandte Produkte und Handbücher für Fernbedingungen Code Alarm PC 7400
Fernbedingungen Code Alarm F65 Wartungshandbuch
(94 Seiten)
(94 Seiten)
Fernbedingungen Code Alarm F65 Bedienerhandbuch
(98 Seiten)
(98 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern