Code Alarm 4000 Betriebsanleitung PDF herunterladen

FAULT FINDING GUIDE

CUSTOMER HAD AN ALARM Ask them to press the Full set button and tell you

what indicators are on. The LED's indicate the cause of the alarm and also the setting

status at the time.

MAINS LED FLASHING Mains failure (Restore supply)

ZONE LED FLASHING (in exit) Check that doors and windows are closed.

Flashing with tamper LED. (A detector has an open tamper).

Flashing with Battery LED. (The detectors battery needs replacing).

ALARM LED ON Full alarm. The LEDs indicate what caused the alarm.

If Engineer reset is programmed into the panel an engineer reset will be required before

the system can be re-armed.

Flashing with zone LED A detector on soak test has triggered whilst the

system was armed.

Flashing without a zone LED An engineer reset is required.

BATTERY LED ON The control panel's battery is disconnected or needs replacement.

Flashing with zone LED Detector has a low battery. The zone LED will flash

indicate which one.

SIGNALLING LED ON The system is being blocked by a continuous transmission.

CONTACT TRANSMITTER NOT WORKING Check the magnetic contact is operating

correctly. Open lid and check what zone it should be on. Go into the panel engineer mode

and check if it has been programmed onto the correct zone.

Note: the panel will not allow you to program a detector onto two zones. When pro-

grammed onto a zone any previous zone allocation will be deleted.

PIR NOT WORKING The detector needs 6 minutes to settle on power up.

Set the control into operator walk test mode and walk test the detector with the

cover removed. Removing the cover opens the tamper and overrides the 2 minute inhibit

timer.

If the test jumper inside is fitted and the cover replaced it overrides the 2 minute inhibit,

but allows you to walk test it without a tamper alarm.

CUSTOMER HAS FORGOTTEN THEIR CODE Open the panel and short out the MEM

jumper. The user and engineer codes will be restored to the factory defaults 1234 & 4679.

No other programming is affected.

FM4000E

CONTROL PANEL

INSTALLATION INSTRUCTIONS

ZONES

FM Electronics Ltd Manufacturer of quality wireless products

CI-146 ISS 1

PANIC

FIRE

FULL SET

PART SET

OFF

SIGNALLING

LOW

BATTERY

ALARM

MAINS ON

TAMPER

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - CONTROL PANEL

FAULT FINDING GUIDECUSTOMER HAD AN ALARM Ask them to press the Full set button and tell youwhat indicators are on. The LED's indicate the cause

Seite 2

++__56879432143215678ANTENNAGROUNDTAMPERMEMJumper+ LATCH-ve SIREN-ve STROBE-ve DIALLER17V a.c.InputEXITSOUNDERVolume leveladjustLink 5 to 4 if -vefrom

Seite 3 - SAB CONNECTION TO THE FM4000

29Bell sw-Bell sw+Tamper feedTamper returnStrobe +Strobe --ve Hold off+ve Hold off71358Connections on the FM4000 main boardSAB CONNECTION TO THE FM40

Seite 4 - PROGRAMMING

3 8PROGRAMMING1. Enter the engineers code 4 6 7 9The Alarm led will flash slowly to indicatethat you are in the program mode.2. Key in the two digi

Seite 5 - * = FACTORY DEFAULT

471= Yes O= No*Press the full set key to exit.34 JAMMING1 = Jamming generates a full alarm whensetO= indicator only*Press the full set key to e

Seite 6

6521 WALK THROUGH ZONESThe factory default is none.The zone LED's indicate which zones arewalk through during entry.Use the keys 1 to 8 to selec

Weitere Dokumente für Auto Alarmanlage Code Alarm 4000

Um das Dokument anzuzeigen Code Alarm 4000 Bedienungsanleitung

Code Alarm 4000 Bedienungsanleitung (16 Seiten)

Code Alarm 4000 Bedienungsanleitung (116 Seiten)

Code Alarm 4000 Bedienungsanleitung (162 Seiten)

Code Alarm 4000 Bedienungsanleitung (23 Seiten)

Code Alarm 4000 Bedienungsanleitung (24 Seiten)

Um das Dokument anzuzeigen Code Alarm 4000 Technical Information

Code Alarm 4000 Technical Information (188 Seiten)

Code Alarm 4000 Bedienungsanleitung (4 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Code Alarm 4000 Betriebsanleitung

Stöbern Sie online oder laden Sie Betriebsanleitung nach Auto Alarmanlage Code Alarm 4000 herunter. Code Alarm 4000 Operating instructions Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Auto Alarmanlage Code Alarm 4000

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Auto Alarmanlage Code Alarm 4000